Unconfigured Ad

**tahustvedt** · 05-02-19, 22:22

Skal prøve både børstemotorer og børsteløs.

Børsteløst oppsett:
https://hobbyking.com/en_us/yep-7a-1...ontroller.html
https://hobbyking.com/en_us/turnigy-...ess-motor.html

Oversky MXL-RX62H V3 RC Airplane Receiver Integrated with Dual Servo for Frsky DSMX DMS2 FUTABA SFHSS

https://www.banggood.com/Oversky-MXL-RX62H-V2-Receiver-Integrated-with-Dual-Servo-for-Frsky-DSMX-DMS2-FUTABA-SFHSS-p-1332998.html

Only US$32.90. Get the Oversky MXL-RX62H V3 RC Airplane Receiver Integrated with Dual Servo for Frsky DSMX DMS2 FUTABA SFHSS at Banggood. It is compatible with multiple transmitter systems.

1.7g Low Voltage Micro Digital Servo Mini JST 1.25Pin Connector for RC Model

https://www.banggood.com/1_7g-Low-Voltage-Micro-Digital-Servo-Mini-JST-Connector-for-RC-Model-p-1157620.html?rmmds=search&cur_warehouse=CN

Only US$22.55. Get precise control with this 1.7g low voltage micro digital servo. Perfect for RC models, it features a mini JST 1.25Pin connector. Buy now at Banggood!

+ 1S 450 mAh

**tahustvedt** · 05-02-19, 22:25

Den har ganske bra vingeareal egentlig. 25-29 g/dm² vingebelastning, hvis mattematikken min er rett. 3,87 dm² vingeareal.

***Karmann*** · 05-02-19, 22:32

Spennende!

Du må holde oss oppdatert?

***Lars N*** · 05-02-19, 22:34

Dæven. Er du ferdig med hele allerede? Du er helt rå......

**tahustvedt** · 05-02-19, 23:14

Noen som vet om det er grei vingebelastning? Vanskelig å finne noe å sammenligne med.

**tahustvedt** · 06-02-19, 12:11

Har akkurat vært ute og flydd den røde friflukt med nok ballast til å veie 109 g totalt. Den fløy helt fantastisk. Dette blir bra! Den blir nok helt fantastisk på hangkanten også.

***Lars N*** · 06-02-19, 12:19

Så bra, dette lover jo veldig bra

***Karmann*** · 06-02-19, 13:37

Tenker du å bruke 4 små motorer eller 2 litt større + 2 dummy(roterende) propeller?

**tahustvedt** · 06-02-19, 14:28

Jeg skal ha fire.

**tahustvedt** · 06-02-19, 18:54

Jeg skrev feil ang den lille Lynxen. Den er 1:32-skala, ikke 1:48.

**tahustvedt** · 07-02-19, 18:57

Micro C-130 Hercules RC model

https://cults3d.com/en/3d-model/various/micro-c-130-hercules-rc-model

EDIT - 15.03.2020: Added new wing parts that can be printed completely with vase mode for better print quality and easier printing with LW-PLA. Also added Aileron02 and Elevator02 which print in one piece for vase mode, and need to be separated after printing. Wingspan: 610 mm Length: 433 mm AUW: 100-115 g CG: ~20mm from the leading edge of the wing center section. For experienced users. It requires basic modeling skills to set up the control surfaces and build the plane. I have not flown the plane under power yet, but I have flown it freeflight with ballast and AUW 109 g. It flies well. Print settings: Mine were all printed on normal printers witnh normal PLA and 0,4 mm nozzles. You can print thinner than 0,4 mm perimeters just fine with a 0,4 mm nozzle. Print most parts with one 0,25 mm perimeter and 0,12 mm layer height. Use two bottom layers and four top layers for most parts. Add top layers as necessary to fill the top. Print Fuselage02 with 0 top layers. Fuselage01 will go into the open end of Fuselage02. Cut away the bottom layers after printing to lighten the model, as shown in the photo of the backside of the green part Fuselage01. as a reference, Fuselage01 should weigh ~6,5 g off the printer and ~5,5 g after trimming down the rear face. I use scissors like these to cut around the inside:https://rover.ebay.com/rover/1/710-53481-19255-0/1?ff3=4&toolid=11800&pub=5575353675&campid=5338226872&mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fitm%2FCurved-Lexan-Scissors-RC-Car-Bodyshell-Cutting-For-Polycarbonate-Shells-Arches-%2F371079169069 Hinge elevators with Blenderm on the top surface. Hinge ailerons with Blenderm on the bottom surface. Hinge the rudder with tiny pieces of CA hinge. Use 0,8 mm piano wire to connect the elevators together. Use 0,8 mm piano wire to greate a torque link to the rudder. Use 0,8 mm piano wire to create torque links to the ailerons in the slots in the bottom of the wing. Required hardware: 1 mm carbon rods 2 mm carbon rods 3 mm carbon rods 0,8 mm piano wire CA glue CA hinge Blenderm hinge tape Can be used with 8,5 mm coreless motors or tiny outrunners. https://hobbyking.com/enus/turnigy-d0703-10000kv-brushless-motor.html?affiliatecode=BSFWYBUNYWDKXJN&_asc=5338582182 Suggested electronics: Receiver and rudder/elevator servo: https://www.banggood.com/custlink/33K3dSpugG Aileron servo: https://www.banggood.com/custlink/vGDmdSrueL 450 mAh 1S lipo. Motors: https://hobbyking.com/enus/turnigy-d0703-10000kv-brushless-motor.html?affiliatecode=BSFWYBUNYWDKXJN&asc=3215844319 ESCs: https://hobbyking.com/enus/yep-7a-1-2s-brushless-speed-controller.html?affiliatecode=BSFWYBUNYWDKXJN&asc=2672935468

***Lars N*** · 07-02-19, 19:21

Originally posted by tahustvedt

https://cults3d.com/en/3d-model/vari...cules-rc-model

Må få ferdig en jobbprosjekt som tar all tid hos meg nå, men til slutten av neste uke skal jeg printe en

**tahustvedt** · 09-02-19, 14:15

Jeg har printet en Fuselage01 som veier 4,2 g. Det er veldig lett, så jeg tror jeg skal prøve å lage en som er 1:72-sala.

For å få 1:72 så skaleres delene til 93,5%.
For å få 1:48 skaleres delene til 140,3%.

***Lars N*** · 09-02-19, 17:59

Originally posted by tahustvedt

Jeg har printet en Fuselage01 som veier 4,2 g. Det er veldig lett, så jeg tror jeg skal prøve å lage en som er 1:72-sala.

For å få 1:72 så skaleres delene til 93,5%.
For å få 1:48 skaleres delene til 140,3%.

Det er imponerende vekt altså. Kanskje man skulle testet 1:48 med en gang. kanskje enklere med tanke på utstyr?

**chewbaca** · 09-02-19, 18:31

Printing pågår ..

Unconfigured Ad

Mikro-Hercules

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Forum Bottome ADS